Toshiba x100 manual




















Do not subject the transducers to knocks. Use of defective transducers may cause an electric shock. Use the system only on a level floor. Doing so may result in the system falling over and causing an injury. Malfunctions due to radio waves 1 Use of radio-wave-emitting devices in the proximity of this kind of medical electronic system may interfere with its operation.

Do not bring or use devices which generate radio waves, such as cellular telephones, transceivers, and radio controlled toys, in the room where the system is installed. This is necessary to ensure the proper operation of the system. Lock the casters once the system is moved to its installation location. Otherwise, the system may move unexpectedly, injuring the patient or operator or hitting nearby objects. If the system is moved to the left or right, it may fall, causing injury.

To prevent electric shock, do not connect the peripheral devices video printer, DVD recorder, etc. Peripheral devices should be connected to the service outlet of the system. Do not place any objects on top of the monitor. They may fall, causing injury. Do not allow fluids such as water to contact the system or peripheral devices.

Electric shock may result. Before starting leakage current measurement, be sure to connect an isolation transformer between the testing device for the electrical safety check and the wall socket. To prevent electric shock, follow the instructions below. The aluminum foil should enclose the electrode. Be sure to turn OFF the power breaker, disconnect the mains plug from the outlet, and wait at least 30 seconds before removing the covers of the main unit and performing internal wiring or other work.

When discarding any part of this system, follow all applicable local regulations. Wear protective gloves to ensure safety and prevent infection when performing unit replacement, board replacement, internal wiring, or cleaning.

Wait at least 30 seconds after turning OFF the power breaker and disconnecting the mains plug from the outlet before replacing the battery. Otherwise, an electric shock may result. Connecting devices other than those recommended may cause the consumption current to exceed the power capacity of the main unit, possibly resulting in malfunction. Removing and cleaning the air filters Do not start the system with the filters removed.

When the patient leakage current is measured, there must be some physiological saline solution between the transducer and the aluminum foil. Preventive maintenance is necessary to avoid the occurrence of malfunctions and to maintain optimal performance of the system up to the end of its service life.

The purpose of regular maintenance and inspection is to maintain the safety, reliability, and essential performance of the system, thus ensuring that high-quality diagnostic information is consistently obtained.

Clean it depending on its condition or the system environment. Measurements related to electric safety are particularly sensitive to the humidity. These measurements are also sensitive to the measurement location and measurement circuit. If the insulation characteristics deteriorate due to system changes over time or system malfunctions, the measurement fluctuations are likely to increase with the increase in humidity. Make a hard copy of the preset conditions used normally and file it in the log book.

Remove the accessories. Remove the covers of the main unit. Clean the interior of the system and the fan. Clean the filters. Clean the covers and panels.

Clean the touch panel. Clean the LCD monitor. Clean the peripheral devices and accessories. Clean the power supply cord and the cables. Tools Phillips screwdriver 2 Remove accessories such as the transducer, transducer holder, and peripheral devices from the main unit. Do not remove any PWBs unless it is abnormal.

Vacuum cleaner 6 On the vinyl bag, make an opening as large as can allow the nozzle of the blower to be inserted and blow out dust on the monitor, fan, PWBs, rack, power supply, etc. If necessary, spray neutral detergent onto a piece of soft, finely woven cloth and use it to clean the covers and panels.

Use cotton swabs to clean areas around the switches and keys on the main panel. A04 2. What is the weight of the Toshiba Camileo X? The Toshiba Camileo X has a weight of g. What is the screen size of the Toshiba Camileo X? The screen size of the Toshiba Camileo X is 3 ". What is the height of the Toshiba Camileo X? The Toshiba Camileo X has a height of What is the width of the Toshiba Camileo X? The Toshiba Camileo X has a width of Reviews Projectors Screens Accessories. Projector Database 11, Projector Forums Login.

Large Venue Classroom Interactive Conference. Find a Projector. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website.

These cookies will be stored in your browser only with your consent.



0コメント

  • 1000 / 1000